5
Litematic
MIN.2sec
Power supply
HOLD
NOM
MIN.30ms
MAX.30ms
MIN.16ms MIN.16ms
PA, PB
*Not available during key input,
RS-232C input, and Digimatic data processing
L1
Max.
Min.
L3
L5
( ) indicates a value in the Smoothing
MAX.16(100)ms
MAX.16(100)ms
DATA
MODE•UP•DN
MIN6ms
MAX12ms
MIN12ms MIN12ms
SET1,2
MIN.15ms
MIN.15ms
Peak clear input (after input HOLD, input preset)
* The value in ( ) is that at the time of sommthing.
**In the case of parameter 28 and HOLD selection 1.
MIN. 0ms
MIN.15ms
HOLD
P.SET
Data latch MAX.10µs (±100ms)*
MAX.30ms Data output**
MAX.20ms* MIN.10ms
Command
Response output
*RS output is suspended during key operation.
LF LF
LF
RS 232C command input
and its output operation
Power on characteristics MODE/.UP/DN timing
External presetting
Tolerance judgment
result output timing
HOLD/PSET timing
+5V
5KΩ
74HC14 or
the equivalent
0.01µF
TD62583 or
the equivalent
Output voltage: MAX. 24V
Output current: MAX. 20mA
Saturation voltage: MAX. 0.7V
Counter External device
Reference circuit
Counter
External device
Reference circuit
+5V
5KΩ
0.01µF
5KΩ
Use open-collector
output or relay output,
etc
Input current: MAX. 1mA
Input voltage(H): 4-24V
(L): MAX.1V
18 1
36
Receptacle
10236-52A2
(3M) or the equivalent
19
Peak Mode SET2 SET1
Current value H H
MAX H L
MIN L H
TIR L L
Speed SET2 SET1
8mm/s H H
4mm/s H L
2mm/s L H
1mm/s L L
Speed SET2 SET1
8mm/s H H
4mm/s H L
2mm/s L H
1mm/s L L
Timing Chart
• RS-232C data output time
The maximum output time with the data output command (GA00CRLF) is calculated
by the following formula.
Max.output time [Unit:ms] = [Number of connected counters] x 20 +
[Number of link channels] x 17 (8.5) + 6 (3)
*Baud rate: 9600bps; the value in ( ) is that for 19200bps.
(Calculation example) One unit of VL: Max. 43 (31.5) ms
Note: The PC processing time is not included.
When changing the spindle
speed, stop the spindle once
and allows 50ms or more
before change.
When changing the spindle
speed, stop the spindle once
and allows 50ms or more
before change.
Output circuit:
Transistor turned ON at “L” (open-collector output)
Input circuit:
Input enabled at “L”
Input/Output circuit
Applicable plug: No. 02ADB440
(with cover) Optional accessory
Connector terminal Function
Pin assignment
Pin No.
Signal Input/
Description (purpose)
name Output
1 COM — Common terminal to input and output circuits
(internally connected to GND)
2 COM —
3L1OUT Tolerance judgment output terminal
4L2OUT A related judgment terminal only outputs “L”
5L3OUT At error occurrence
6L4OUT L1, L5: Outputs “L”
7L5OUT L2, L3, L4: Outputs “H”
10 NOM OUT Outputs “L” in the count mode.
21 ULIMIT OUT Outputs “L” at the top dead point of the spindle
22 WORK OUT Outputs “L” upon detection of a workpiece.
25 SET1 IN Specifies peak selection/motor speed in
combination with SET.
26 SET2 IN
28 MODE IN Peak selection: In combination with SET.
30 UP IN Motor control: Specifies a spindle ascent speed
along with SET.
31 DN IN Motor control: Specifies a spindle descent speed
along with SET.
32 FSW IN Motor control: Same function as that of the foot
switch.
34 HOLD IN The display value is held during input.
An error is cleared at the leading edge of this
signal.
35 P.SET IN Executes presetting.
Peak clear: The peak is cleared upon input of the
P.SET signal during the HOLD signal input in the
Peak mode.
N.C. — Unconnected terminal (Connect nothing)
(8, 9, 11, to 20, 23, 24, 27, 29, 33 and 36 pin
terminals)
(36 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern